tarm 3 OUTDOOR

Outdoor laser, perfectly suitable for fixed installations for advertising, mappings or any kind of graphics projections. The high quality beam with uniform beam profile, combined with the fast scanning and upgrade option to CT-6210, makes the tarm 3 OUTDOOR a great projection unit.
IP65 waterproof laser system, suitable for outdoor use and fixed installations.
  • IP65 waterproof housing
  • 3'000 mW guaranteed power
  • Graphics capable - 45kpps @ 8° ILDA Scanners
  • Full color mixing - analog modulation
  • Extremely sharp intense beams - low divergeance of <0.6 mrad
  • Control screen (internal) for convenient mode selection
  • Free computer control software - Showeditor - upgradable to Showcontroller
  • Integrated powerful mainboard with advanced configuration features (geo-correction, zone setup, color balancing, etc.) and DAC feature
  • Multiple control modes - stand-alone, ArtNET, LAN and ILDA streaming

ShowNET mainboard as standard:
  • Various control options: Professional Art-Net (two modes), Stand-Alone Operation, ILDA Streaming Receiver, LAN (Computer control, integrated DAC)
  • Create custom content, store it inside the laser and play it back in different modes
  • Free laser show control software included
Stand-Alone modeSTAND-ALONE MODE:
The laser operates stand-alone and does not need and control. It plays back the content stored on the laser's mainboard.
ArtNET modeArtNET Control mode
LAN connectionLAN MODE:
The laser can be controlled over LAN - this can be either direct software control, or ArtNET or similar (depending on the main board)
ILDA StreamingILDA Streaming
The laser is equipped with the advanced ShowNET laser mainboard which brings a multitude of features to the laser and makes it an intelligent lighting device.
Free Showeditor laser software includedSHOWEDITOR INCLUDED:
The full version of the laser show control software Showeditor is included in delivery.
The tarm 3 OUTDOOR are especially designed for outdoor laser installations. They come equipped with the top quality laser setup known from the standard tarm units, but have a waterproof enclosure that not only protects the components inside from water, but also shields off direct heat from solar exposure. A specially designed roof in front of the output window prevents it from getting impacted by direct rain. To cope with varying temperatures, the tarm OUTDOOR units are equipped with an active watercooling system, that is built into the housing. An active heating system helps to keep the laser systems operational even at low temperatures. Thus the tarm 3 OUTDOOR lasers can be used at environmental temperatures between -10°C and +45°C. A CT Scanner upgrade with LAS Turboscan drivers is available for the tarm 3 OUTDOOR to achieve top end quality graphics results.

The tarm 3 OUTDOOR show laser projector is a full color whitelight RGB laser systems with full analog color modulation and diode-only equipment. The guaranteed output power is specified at 3'000 mW after optics.

The tarm 3 OUTDOOR units have a built-in network DAC for Showcontroller, Showeditor, Touchdesigner, MadLaser, etc., but also can be controlled with any ILDA laser control software such as Pangolin Quickshow, Pangolin Beyond, LSX, Lasergraph DSP, etc. via external ILDA interface (e.g. FB3) and ILDA streaming. They also have a built-in memory with pre-set patterns, that can be easily triggered through ArtNet and automatic mode.
The tarm 3 OUTDOOR comes with integrated ShowNET network interface and free laser show software. Details in the box below.

The benefits include:

  • 3'000 mW guaranteed output power
  • a very fast maximum scan speed of 45kpps @ 8° ILDA for graphics projection
  • high-precision diode arrays provide an excellent beam divergence of less than <0.6 mrad for a low beam diameter
  • pure diode laser
  • novel method for increasing the beam precision of the diodes
  • beautiful colors and good color fading
  • the tarm 3 OUTDOOR impresses with very bright 637 nm red diodes


The tarm 3 OUTDOOR laser has great beam specifications with a diameter of ca. ca. 4.5 mm and a beam divergence of less than <0.6 mrad.
It is equipped with a bright red (1'000 mW / 637 nm), a green (900 mW / 520 nm), and a blue (1'700 mW / 450 nm) diode laser source.

The scanners are very fast with 45kpps @ 8° ILDA standard and allow for a maximum scan angle of 50°. Thus they are well graphics capable and suitable for professional laser applications.
Optionally as upgrade available: CT-6210 scanners with 60 kpps@8° ILDA and a max. scan angle of 60°.

+ Integrated ShowNET incl. free laser show software

The tarm 3 OUTDOOR features an integrated ShowNET network interface with free laser control software included!
Start with your own professional laser show thanks to the intuitive Showeditor laser show software which comes with every new tarm 3 OUTDOOR for free. The Showcontroller software is supported as well and can be purchased additionally.
The integrated ShowNET allows for direct input through ILDA and LAN. It is also possible to trigger single frames via ArtNet. Custom frames and shows can be played from an integrated SD card (included in delivery) – even in stand-alone mode!
There are two different ArtNet modes:
(1) DJ Mode with the most used features for beginners. Only a few channels are used for a quick and easy access to the most important adjustments directly at the laser system.
(2) Professional Mode with all ArtNet features especially for users with an ArtNet capable console. All adjustments can be triggered and allow for full control of the professional laser show.
The integrated ShowNET works as DAC (digital to analog converter) and enables ILDA streaming.


> More details

Optional control options (modification required!):

Optional control options require modifications to the general laser setup. Other operation modes or compatibilities may get lost.
Pangolin Logo
Pangolin Logo


> More details

Tarm 3 OUTDOOR L S Detail
Tarm 3 OUTDOOR R S Detail
Tarm 3 Graphics19 Beam
Tarm 3 Graphics7 Beam
Tarm 3 Graphics16 Beam
Tarm 3 Graphics6 Beam
Tarm 3 Graphics5 Beam
Tarm 3 Graphics17 Beam
Tarm 3 Graphics18 Beam
Tarm 3 Graphics8 Beam
Tarm 3 Graphics15 Beam
Tarm 3 Graphics9 Beam
Tarm 3 Graphics14 Beam
Tarm 3 Graphics11 Beam
Tarm 3 Graphics12 Beam
Tarm 3 Graphics10 Beam
Tarm 3 Graphics13 Beam
Tarm 3 Graphics4 Beam
Tarm 3 Graphics3 Beam
Tarm 3 Graphics1 Beam
Tarm 3 Graphics2 Beam


> More details

Guaranteed Power at aperture
3'000 mW
Power Red
1'000 mW / 637 nm
Power Green
900 mW / 520 nm
Power Blue
1'700 mW / 450 nm
Beam Specifications*
ca. 4.5 mm / <0.6 mrad
45kpps @ 8° ILDA; optional: CT-6210 with LAS Turboscan: 60kpps @ 8° ILDA, max. 60°
Max. Scan Angle
Laser Source
Laser Class
Operation Modes
LAN, ArtNet, ILDA Streaming, integrated SD card, stand-alone
Basic Patterns
over 120 (layers, tunnels, fences, waves, etc.)
Incl.power cable, manual, E-Stop, interlock connector, full version Showeditor software license included
IP rating
Power Supply
85 V - 250 V / AC, 50/60 Hz
Power Consumption
300 W
800 / 370 / 260 mm
22 kg
*Due to Advanced Optical Correction technology used in our laser systems the optical power of each colour within installed laser module(s) may slightly differ from the specification of respective laser module(s). Divergence FWHM average depending on model.


> More details


Distributed brands:

Distributed Brand LaserworldDistributed Brand tarmdistributed brand Ray Technologies
Distributed Brand Laserworld ShoweditorDistributed Brand ShowcontrollerDistributed Brand PangolinDistributed Brand coherent