Downloads

Downloads

Downloads, Manuals

Download details

Laserworld Manual Laser Module SwissLas BLUE4500-445 2011 Laserworld Manual Laser Module SwissLas BLUE4500-445 2011

e-max.it: your social media marketing partner
Information
Version2011
Size634.57 KB
MD5 Checksum7442abf185ad84bed3b98f1f6c716a4c
Mirrors:

Text in this document

Laserworld Ads:
Find more products:
Swisslas Lasermodule BLUE4500 - 445 Manual Please read carefully before use DANGER LASER RADIATION! Danger for eyes and skin. All protective measures for a safe operation of this laser must be applied. Safety instructions Make sure to use the correct voltage. T he operator has to ensure that laser radiation ̀琀 also reflected laser radiation ̀琀 higher than the maximum permissible level is avoided by technical or organisational measures. Always ensure that the maximum permissible exposure (MPE) is n ot exceeded in the area accesible to the public. In some countries, the operator must notify the insurance and the authorit ies for industrial safety ĀༀĀḀĀ⠀Ā紀Ā谀ĀḀ�̀Ā紀Ā褀ĀḀĀ谀ĀȀĀ騀Ā崀Ā瘀Ā倀�̀ĀȀ�̀Ā漀ĀȀĀ退ĀḀĀ谀̀堀�̀�☀Ā紀Ā谀�̀Ā甀Ā紀Ā谀ĀḀ�̀Ā崀Ā瘀Ā⠀Ā紀Ā谀Ā甀ĀȀĀ騀Ā崀Ā紀Ā瘀̀唀�̀ĀကĀ紀Ā瘀Ā騀ĀȀĀကĀ騀�̀Ā騀Ā娀ĀḀ�̀Ā谀ĀḀĀ漀ĀḀĀ쀀ĀȀĀ瘀Ā騀�̀ĀȀĀ딀Ā騀Ā娀Ā紀Ā谀Ā崀Ā騀Ā崀ĀḀĀ退̀堀�̀�᠀Ā紀Ā瘀̀嬀Ā騀�̀Ā딀Ā退ĀḀ�̀Ā騀Ā娀ĀḀ�̀Ā甀Ā紀ĀᨀĀ딀Ā漀ĀḀ�̀Ā崀Ā⠀�̀ h ousing, or electrical pars are visibly damaged. Do not turn device on and immediately off again frequently. Always disco nnect from mains, when handling or installing the laser . Do not look into the laser beam directly, especially not with optical instruments. Do not touch the device with wet hands. When the laser diode becomes dim or broken, please contact your dealer timely. Laserworld Swisslas BLUE4500 - 445 Lasermodul High end Swisslas blue diode laser - used in collimation, scientific experiment ation, o ptics instrument, laser display and lighting etc. IMPORTANT Mounting of SWISSLAS MODULES all Powerranges Swisslas Ā甀Ā紀ĀᨀĀ딀Ā漀ĀḀĀ退�̀ĀȀĀ谀ĀḀ�̀ĀᨀĀḀĀ漀Ā崀Ā쀀ĀḀĀ谀ĀḀĀᨀ�̀Ā섀Ā崀Ā騀Ā娀Ā紀Ā딀Ā騀�̀Ā娀ĀḀĀȀĀ騀�̀Ā退Ā崀Ā瘀Ā氀̀堀�̀�ⰀĀ紀Ā섀ĀḀĀ쀀ĀḀĀ谀̀唀�̀Ā崀Ā騀̀嬀Ā退�̀Ā쀀ĀḀĀ谀Ā윀�̀Ā崀Ā甀Ā褀Ā紀Ā谀Ā騀ĀȀĀ瘀Ā騀�̀Ā騀Ā紀�̀Ā딀Ā退ĀḀ�̀ĀȀ�̀Ā娀ĀḀĀȀĀ騀�̀Ā退Ā崀Ā瘀Ā氀�̀Ā紀Ā谀�̀Ā退Ā崀Ā甀Ā崀Ā漀ĀȀĀ谀�̀ cooling device. Operating without a heat sink will damage the module in less then one minute. This heat sink has to be very planar. If it is not, the beam s will not be in one line and the module will be disaligned. B etween the SwissLas Module and your heat please use some steel plain washers with 0.1 to 0.3mm thickness at the screw . Use the thinnest possible plain washers, but it is important that they are at least as thick as the non - flatness of your heat sink. Use thermal compound between your heat sink and the ground - plate of the Laser module . I t is very important to fill the complete gap! We don't take on any cost for the repairs of any possible failures according to incorrect mounting! Left image: The heat sink has to be directly beneath the laser module. �栀Ā退ĀḀ�̀Ā騀Ā娀ĀḀĀ谀Ā甀ĀȀĀ漀�̀Ā倀Ā谀ĀḀĀȀĀ退ĀḀ�̀Ā딀Ā瘀ĀᨀĀḀĀ谀�̀Ā騀Ā娀ĀḀ�̀�搀�ᰀ�ሀ�̀ĀḀĀ漀ĀḀĀ甀ĀḀĀ瘀Ā騀�̀Ā紀Ā⠀�̀Ā騀Ā娀ĀḀ�̀Ā漀ĀȀĀ退ĀḀĀ谀�̀̀縀ĀᨀĀ紀Ā瘀̀嬀Ā騀�̀Ā紀Ā쀀ĀḀĀ谀Ā騀Ā딀Ā谀Ā瘀�̀Ā騀Ā娀ĀḀ�̀Ā甀Ā紀Ā딀Ā瘀Ā騀Ā崀Ā瘀Ā倀�̀Ā退ĀကĀ谀ĀḀĀ섀Ā退̀唀�̀Ā騀Ā娀ĀḀ�̀�搀�ᰀ�ሀ�̀ĀကĀ紀Ā딀Ā漀Āᨀ�̀ break): Centre image: Use 3 screws to mount the module (2 on one side, one centred on the other, see image), to avoid bending of the mounting plate. Use thin washers (0.1mm) to compensate for unevenness of the surface. Right image: Use a good heat sink with a strong fan. Also use thermal grease between heat sink and mounting plate. The temperature of the module may not exceed 40C ̀琀 if it is exceeded the module will reduce output power (to ca. 50%) to protect the diodes! Connectors: Caution: Do not switch supply voltage and ground ̀琀 this will damage the driver! You can supply TEC and Diode from one, or two separate PSUs ̀琀 always connect both pins 3 and 5 to the PSU ground connection. When using single ended modulation (one side connected to ground) connect pin2 to gnd! Fuse changing Fuse 2.5A for Diode Please solder the new fuse according this picture Fuse 5A fo...


Distributed brands:

logo-laserworldlogo-swisslasHB-Laserlogo-ray-technologies-rti
logo tarm
logo-pangolinlogo-coherentlogo-wireless-solutionsint visionsSpider-Laser-Game

logo-vplt-foerderndes-mitgliedilda logo black cleanedup 2006 member


Contact us:
ch +41-71-6778080
en +44-161-8188969

 

You agree to the disclaimer of this page with using it.